SpinCAD Designer can now export 8 patches to a Spin Project

[Digital Larry]

Yes folks, it's the bleeding edge experimental version 0.98/969 currently, but you can:

- load and quickly switch between 8 patches in the workspace.
- copy and paste full patches or just a group of blocks, within a patch or between 2 patches
- simulate patches on your PC to get a better sense of level balance etc.
- export a bank of 8 patches to a hex file
- export a bank of 8 patches to Spin ASM (8 .spn files) and Spin Project (.spj file)

You can load the Spin Project file into the Spin IDE to send your bank of 8 patches to the Spin Dev board.

With the Hex file you should be able to program your EEPROMs directly using something like the PICKit2. Although to be honest I haven't personally tested that yet.

SpinCAD Designer is still free and will always be open source!

http://holycityaudio.com/forum/

[sunfalls]

this is cool news.
but, i'm completely in the dark with spincad designer.

how on earth do i install this on my Mac.
the instructions leave much to be desired. being i'm not a java compiler/programmer.

i have virtual box running windows for the Spinasm app to burn to my Zdsp cards.

and would absolutely love to be able to use the spincad designer to export the fx program files from my zdsp custom cards.

any assistance would be greatly appreciated.

[Digital Larry]

Sorry you're having trouble using it.

I have a topic over at my forum regarding how to get started. I don't like cluttering up the Spin Forum with too much SpinCAD stuff. Here's the topic:

http://holycityaudio.com/forum/viewtopi ... =32&t=1202

You will have to register there, then you can access the program download. No need to do any programming. That's the whole point!

I'll admit the documentation is a little dodgy. But I check in frequently to assist anyone struggling.

[muccaudio]

I fail when running Java, please ask whether you could help

[Digital Larry]

Please register over at:

http://holycityaudio.com/forum

and I will help you over there. SpinCAD Designer is not supported by Spin.

[dientutrongtoi]

Can you share link download SpinCAD Designer for window?

[ice-nine]

Can you share link download SpinCAD Designer for window?

The link is in the post above your post, register and download.

[leetut]

I never receive a confirmation email to get into that forum, where else can I download spincad?

[ice-nine]

I never receive a confirmation email to get into that forum, where else can I download spincad?

I think the confirmation is done manually so may take a day or two for Digital Larry to send the confirmation. be patient and if no reply after a day or two then I would sugeest giving digital larry here a PM. I'm sure he will sort it out for you.

[mportnoy]

I never receive a confirmation email to get into that forum, where else can I download spincad?

+1. I've been waiting for over a week for the confirmation email. I downloaded the build from GitHub, but unfortunately the instructions don't match what I'm seeing during the install. My Java programming skills are limited at best, and I understand that maintaining documentation for the software is a TON of work. I figure it's easier if I can access the Holy City forum and post questions there rather than bug everyone here.

[leetut]

I think it’s dead, I tried sending an email to the guy that deals with conformation and got this:
Address not found
Your message wasn't delivered to joe@joefriday-lg.com because the domain joefriday-lg.com couldn't be found. Check for typos or unnecessary spaces and try again.

[mportnoy]

I think it’s dead, I tried sending an email to the guy that deals with conformation and got this:
Address not found
Your message wasn't delivered to joe@joefriday-lg.com because the domain joefriday-lg.com couldn't be found. Check for typos or unnecessary spaces and try again.

Same here.

[Digital Larry]

I'm not dead yet!



If you haven't received a confirmation then you didn't read the instructions. Or if you did, I missed your message. But I look fairly regularly.